How to Handle Yellowing Hemp Leaves

Columns - Guest Column

Nitrogen levels may be to blame.

RuggedCoast | Adobe Stock
Stunted growth also occurs when nitrogen (N) levels are inadequate. Note the lack of leaf expansion, which occurred on the new growth due to inadequate nitrogen.
© Brian Whipker

Editor’s note: This article was originally published in the May 2019 issue of Cannabis Business Times.

Out of all the nutrients provided by growers to stimulate plant growth, nitrogen (N) is needed in the largest quantity.

Thus, meeting the N needs of hemp is central to developing a successful fertilization strategy. Because of the volumetric importance of N, it is not surprising that symptoms of N deficiencies often are the first to manifest during production and are the most common health issue growers see. Symptoms of N deficiencies that hemp plants exhibit include pale green lower leaves, lower leaf yellowing and, as symptoms progress, necrosis and plant stunting. All of these symptoms occur when the available N supply is inadequate. Symptoms develop on the lower leaves because N is a mobile element. Plants will move (translocate) N from the lower leaves to the growing tip if inadequate levels are provided. On the opposite end of the spectrum, when N levels are excessive, lower leaf marginal necrosis (burn) occurs.

Nitrogen Management

The concentration of nitrogen that plants need corresponds with where the plant is in its development. Here are the N needs of hemp plants for each life stage, from rooting to flowering.


When plants are being propagated as clones, the nutrient reserves in the cutting can be easily leached out with mist or fog. Nutrient reserves could further be depleted if the cutting was taken from an old mother plant, as reserves in stock/mother plants also diminish over time. As such, it is important to supply a dose of essential nutrients to the cuttings to restore the nutrient reserves. Once roots are visible, provide the plants with 50 ppm to 75 ppm of N two to three times per week to help restore the nutrient levels within the cuttings.


Smaller clones just transplanted into a container are primarily putting their energy into establishing a root system. Therefore, they require lower levels of N, so beginning a constant liquid fertilization program of 100 ppm to 125 ppm N (applied every irrigation) will help jump-start growth.

Lower leaves with a lighter green coloration indicate inadequate nitrogen (N) is being provided to the plant.
© Brian Whipker
As nitrogen (N) deficiency symptoms advance, the lower leaves turn a bright yellow coloration.
© Brian Whipker
With advanced nitrogen (N) deficiency symptoms, the lower leaves will turn from a yellow coloration to a brown coloration, and finally necrotic.
© Brian Whipker
Excessive levels of nitrogen or other nutrients can lead to lower leaf marginal necrosis.
© Brian Whipker
Vegetative Fill Out and Pre-Flowering

Once the roots have reached the edge of the pot and the root system has developed, the plant will start producing vegetative growth. During periods of rapid vegetative growth, hemp plants require a higher concentration of N, so initially you can ramp up N to 150 ppm to 200 ppm for every feeding during the vegetative stage, and then 200 ppm to 225 ppm of N can be used for feedings during the pre-flowering stage. This will help ensure that adequate levels of N are provided as the plant bulks up.


As with any plant that has terminal flowers (including poinsettias and chrysanthemums), the nutrient demands of a hemp plant peak and then decrease throughout the flower period. This makes sense: If the plant is not growing as rapidly, as one can easily measure by the change in plant dry weight, then the amount of N supplied should be dialed back. Thus, a lower level of 100 ppm to 150 ppm of N should be applied at every feeding during peak flowering.

Conducting in-house monitoring of the electrical conductivity (EC) in the substrate will help ensure that the nutrient levels are adequate and not limiting or excessive. (Read more about monitoring EC.)

Corrective Procedures

A straightforward procedure exists to correct an N deficiency: simply increase the N supply for one or two applications to help restore the N reserves in the plant. Applying 300 ppm to 400 ppm of N from a balanced fertilizer such as 13-2-13 Cal-Mag will provide all the essential nutrients to the plant. Other alternative complete fertilizers include 17-4-17 Cal-Mag, 17-5-17 Cal-Mag, or 15-5-15 Cal-Mag. Another option to consider is a dark weather feed (15-0-15) if only N, potassium (K), and calcium (Ca) are desired. If a higher ammoniacal nitrogen (NH4-N) concentration and higher phosphorus concentration are desired to boost vegetative growth and fill out, then a fertilizer such as 20-10-20 can be applied. Apply these corrective procedures as a 10% flow-through leaching irrigation if the plants are grown in pots. This will stop the progression of deficiency symptoms but will not reverse any severely affected chlorotic or necrotic leaves.

Having a balanced fertility program at the target N levels during each stage of production will help ensure that your hemp plants have adequate nutrients and avoid the development of lower leaf yellowing.

Brian Whipker, James Turner Smith & Hunter Landis are from the Department of Horticultural Science, North Carolina State University (NCSU), Raleigh, N.C. Paul Cockson, formerly of NCSU, is from the University of Kentucky, Lexington, K.Y.